Novel Artificial Material Could Facilitate Wireless Power

This advance is made possible by the recent ability to fabricate exotic composite materials known as metamaterials, which are not so much a single substance, but an entire human-made structure that can be engineered to exhibit properties not readily found in nature. In fact, the metamaterial used in earlier Duke studies, and which would likely be used in future wireless power transmission systems, resembles a miniature set of tan Venetian blinds.

Theoretically, this metamaterial can improve the efficiency of"recharging" devices without wires. As power passes from the transmitting device to the receiving device, most if not all of it scatters and dissipates unless the two devices are extremely close together. However, the metamaterial postulated by the Duke researchers, which would be situated between the energy source and the"recipient" device, greatly refocuses the energy transmitted and permits the energy to traverse the open space between with minimal loss of power.

"We currently have the ability to transmit small amounts of power over short distances, such as in radio frequency identification (RFID) devices," said Yaroslav Urzhumov, assistant research professor in electrical and computer engineering at Duke's Pratt School of Engineering."However, larger amounts of energy, such as that seen in lasers or microwaves, would burn up anything in its path.

"Based on our calculations, it should be possible to use these novel metamaterials to increase the amount of power transmitted without the negative effects," Urzhumov said.

The results of the Duke research were published online in the journalPhysical Review B. Urzhumov works in the laboratory of David R. Smith, William Bevan Professor of electrical and computer engineering at Pratt School of Engineering. Smith's team was the first demonstrate that similar metamaterials could act as a cloaking device in 2006.

Just as the metamaterial in the cloaking device appeared to make a volume of space"disappear," in the latest work, the metamaterial would make it seem as if there was no space between the transmitter and the recipient, Urzhumov said. Therefore, he said, the loss of power should be minimal.

Urzhumov's research is an offshoot of"superlens" research conducted in Smith's laboratory. Traditional lenses get their focusing power by controlling rays as they pass through the two outside surfaces of the lens. On the other hand, the superlens, which is in fact a metamaterial, directs waves within the bulk of the lens between the outside surfaces, giving researchers a much greater control over whatever passes through it.

The metamaterial used in wireless power transmission would likely be made of hundreds to thousands -- depending on the application -- of individual thin conducting loops arranged into an array. Each piece is made from the same copper-on-fiberglass substrate used in printed circuit boards, with excess copper etched away. These pieces can then be arranged in an almost infinite variety of configurations.

"The system would need to be tailored to the specific recipient device, in essence the source and target would need to be 'tuned' to each other," Urzhumov said."This new understanding of how matematerials can be fabricated and arranged should help make the design of wireless power transmission systems more focused."

The analysis performed at Duke was inspired by recent studies at Mitsubishi Electric Research Labs (MERL), an industrial partner of the Duke Center for Metamaterials and Integrated Plasmonics. MERL is currently investigating metamaterials for wireless power transfer. The Duke researchers said that with these new insights into the effects of metamaterials, developing actual devices can be more targeted and efficient.

The Duke University research was supported by a Multidisciplinary University Research Initiative (MURI) grant through the Air Force Office of Scientific Research and the U.S. Army Research Office.

Source

Exploring the Superconducting Transition in Ultra Thin Films

"Understanding exactly what happens when a normally insulating copper-oxide material transitions from the insulating to the superconducting state is one of the great mysteries of modern physics," said Brookhaven physicist Ivan Bozovic, lead author on the study.

One way to explore the transition is to apply an external electric field to increase or decrease the level of"doping" -- that is, the concentration of mobile electrons in the material -- and see how this affects the ability of the material to carry current. But to do this in copper-oxide (cuprate) superconductors, one needs extremely thin films of perfectly uniform composition -- and electric fields measuring more than 10 billion volts per meter. (For comparison, the electric field directly under a power transmission line is 10 thousand volts per meter.)

Bozovic's group has employed a technique called molecular beam epitaxy (MBE) to uniquely create such perfect superconducting thin films one atomic layer at a time, with precise control of each layer's thickness. Recently, they've shown that in such MBE-created films even a single cuprate layer can exhibit undiminished high-temperature superconductivity.

Now, they've applied the same technique to build ultrathin superconducting field effect devices that allow them to achieve the charge separation, and thus electric field strength, for these critical studies.

These devices are similar to the field-effect transistors (FETs) that are the basis of all modern electronics, in which a semiconducting material transports electrical current from the"source" electrode on one end of the device to a"drain" electrode on the other end. FETs are controlled by a third electrode, called a"gate," positioned above the source-drain channel -- separated by a thin insulator -- which switches the device on or off when a particular gate voltage is applied to it.

But because no known insulator could withstand the high fields required to induce superconductivity in the cuprates, the standard FET scheme doesn't work for high-temperature superconductor FETs. Instead, the scientists used electrolytes, liquids that conduct electricity, to separate the charges.

In this setup, when an external voltage is applied, the electrolyte's positively charged ions travel to the negative electrode and the negatively charged ions travel to the positive electrode. But when the ions reach the electrodes, they abruptly stop, as though they've hit a brick wall. The electrode"walls" carry an equal amount of opposite charge, and the electric field between these two oppositely charged layers can exceed the 10 billion volts per meter goal.

The result is a field effect device in which the critical temperature of a prototype high-temperature superconductor compound (lanthanum-strontium-copper-oxide) can be tuned by as much as 30 degrees Kelvin, which is about 80 percent of its maximal value -- almost ten times more than the previous record.

The scientists have now used this enhanced device to study some of the basic physics of high-temperature superconductivity.

One key finding: As the density of mobile charge carriers is increased, their cuprate film transitions from insulating to superconducting behavior when the film sheet resistance reaches 6.45 kilo-ohm. This is exactly equal to the Planck quantum constant divided by twice the electron charge squared -- h/(2e)². Both the Planck constant and electron charge are"atomic" units -- the minimum possible quantum of action and of electric charge, respectively, established after the advent of quantum mechanics early in the last century.

"It is striking to see a signature of such clearly quantum-mechanical behavior in a macroscopic sample (up to millimeter scale) and at a relatively high temperature," Bozovic said. Most people associate quantum mechanics with characteristic behavior of atoms and molecules.

This result also carries another surprising message. While it has been known for many years that electrons are paired in the superconducting state, the findings imply that they also form pairs (although localized and immobile) in the insulating state, unlike in any other known material. That sets the scientists on a more focused search for what gets these immobilized pairs moving when the transition to superconductivity occurs.

Superconducting FETs might also have direct practical applications. Semiconductor-based FETs are power-hungry, particularly when packed very densely to increase their speed. In contrast, superconductors operate with no resistance or energy loss. Here, the atomically thin layer construction is in fact advantageous -- it enhances the ability to control superconductivity using an external electric field.

"This is just the beginning," Bozovic said."We still have so much to learn about high-temperature superconductors. But as we continue to explore these mysteries, we are also striving to make ultrafast and power-saving superconducting electronics a reality."

This research was funded by the DOE Office of Science and the Swiss National Science Foundation.

Source

New Solar Cell Technology Greatly Boosts Efficiency

The technology substantially overcomes the problem of poor transport of charges generated by solar photons. These charges -- negative electrons and positive holes -- typically become trapped by defects in bulk materials and their interfaces and degrade performance.

"To solve the entrapment problems that reduce solar cell efficiency, we created a nanocone-based solar cell, invented methods to synthesize these cells and demonstrated improved charge collection efficiency," said Xu, a member of ORNL's Chemical Sciences Division.

The new solar structure consists of n-type nanocones surrounded by a p-type semiconductor. The n-type nanoncones are made of zinc oxide and serve as the junction framework and the electron conductor. The p-type matrix is made of polycrystalline cadmium telluride and serves as the primary photon absorber medium and hole conductor.

With this approach at the laboratory scale, Xu and colleagues were able to obtain a light-to-power conversion efficiency of 3.2 percent compared to 1.8 percent efficiency of conventional planar structure of the same materials.

"We designed the three-dimensional structure to provide an intrinsic electric field distribution that promotes efficient charge transport and high efficiency in converting energy from sunlight into electricity," Xu said.

Key features of the solar material include its unique electric field distribution that achieves efficient charge transport; the synthesis of nanocones using inexpensive proprietary methods; and the minimization of defects and voids in semiconductors. The latter provides enhanced electric and optical properties for conversion of solar photons to electricity.

Because of efficient charge transport, the new solar cell can tolerate defective materials and reduce cost in fabricating next-generation solar cells.

"The important concept behind our invention is that the nanocone shape generates a high electric field in the vicinity of the tip junction, effectively separating, injecting and collecting minority carriers, resulting in a higher efficiency than that of a conventional planar cell made with the same materials," Xu said.

Research that forms the foundation of this technology was accepted by this year's Institute of Electrical and Electronics Engineers photovoltaic specialist conference and will be published in the IEEE Proceedings. The papers are titled"Efficient Charge Transport in Nanocone Tip-Film Solar Cells" and"Nanojunction solar cells based on polycrystalline CdTe films grown on ZnO nanocones."

The research was supported by the Laboratory Directed Research and Development program and the Department of Energy's Office of Nonproliferation Research and Engineering.

Other contributors to this technology are Sang Hyun Lee, X-G Zhang, Chad Parish, Barton Smith, Yongning He, Chad Duty and Ho Nyung Lee.

Source

Toward Optical Computing in Handheld Electronics: Graphene Optical Modulators Could Lead to Ultrafast Communications

The team of researchers, led by UC Berkeley engineering professor Xiang Zhang, built a tiny optical device that uses graphene, a one-atom-thick layer of crystallized carbon, to switch light on and off. This switching ability is the fundamental characteristic of a network modulator, which controls the speed at which data packets are transmitted. The faster the data pulses are sent out, the greater the volume of information that can be sent. Graphene-based modulators could soon allow consumers to stream full-length, high-definition, 3-D movies onto a smartphone in a matter of seconds, the researchers said.

"This is the world's smallest optical modulator, and the modulator in data communications is the heart of speed control," said Zhang, who directs a National Science Foundation (NSF) Nanoscale Science and Engineering Center at UC Berkeley."Graphene enables us to make modulators that are incredibly compact and that potentially perform at speeds up to ten times faster than current technology allows. This new technology will significantly enhance our capabilities in ultrafast optical communication and computing."

In this latest work, described in the May 8 advanced online publication of the journalNature, researchers were able to tune the graphene electrically to absorb light in wavelengths used in data communication. This advance adds yet another advantage to graphene, which has gained a reputation as a wonder material since 2004 when it was first extracted from graphite, the same element in pencil lead. That achievement earned University of Manchester scientists Andre Geim and Konstantin Novoselov the Nobel Prize in Physics last year.

Zhang worked with fellow faculty member Feng Wang, an assistant professor of physics and head of the Ultrafast Nano-Optics Group at UC Berkeley. Both Zhang and Wang are faculty scientists at Lawrence Berkeley National Laboratory's Materials Science Division.

"The impact of this technology will be far-reaching," said Wang."In addition to high-speed operations, graphene-based modulators could lead to unconventional applications due to graphene's flexibility and ease in integration with different kinds of materials. Graphene can also be used to modulate new frequency ranges, such as mid-infrared light, that are widely used in molecular sensing."

Graphene is the thinnest, strongest crystalline material yet known. It can be stretched like rubber, and it has the added benefit of being an excellent conductor of heat and electricity. This last quality of graphene makes it a particularly attractive material for electronics.

"Graphene is compatible with silicon technology and is very cheap to make," said Ming Liu, post-doctoral researcher in Zhang's lab and co-lead author of the study."Researchers in Korea last year have already produced 30-inch sheets of it. Moreover, very little graphene is required for use as a modulator. The graphite in a pencil can provide enough graphene to fabricate 1 billion optical modulators."

It is the behavior of photons and electrons in graphene that first caught the attention of the UC Berkeley researchers.

The researchers found that the energy of the electrons, referred to as its Fermi level, can be easily altered depending upon the voltage applied to the material. The graphene's Fermi level in turn determines if the light is absorbed or not.

When a sufficient negative voltage is applied, electrons are drawn out of the graphene and are no longer available to absorb photons. The light is"switched on" because the graphene becomes totally transparent as the photons pass through.

Graphene is also transparent at certain positive voltages because, in that situation, the electrons become packed so tightly that they cannot absorb the photons.

The researchers found a sweet spot in the middle where there is just enough voltage applied so the electrons can prevent the photons from passing, effectively switching the light"off."

"If graphene were a hallway, and electrons were people, you could say that, when the hall is empty, there's no one around to stop the photons," said Xiaobo Yin, co-lead author of the Nature paper and a research scientist in Zhang's lab."In the other extreme, when the hall is too crowded, people can't move and are ineffective in blocking the photons. It's in between these two scenarios that the electrons are allowed to interact with and absorb the photons, and the graphene becomes opaque."

In their experiment, the researchers layered graphene on top of a silicon waveguide to fabricate optical modulators. The researchers were able to achieve a modulation speed of 1 gigahertz, but they noted that the speed could theoretically reach as high as 500 gigahertz for a single modulator.

While components based upon optics have many advantages over those that use electricity, including the ability to carry denser packets of data more quickly, attempts to create optical interconnects that fit neatly onto a computer chip have been hampered by the relatively large amount of space required in photonics.

Light waves are less agile in tight spaces than their electrical counterparts, the researchers noted, so photon-based applications have been primarily confined to large-scale devices, such as fiber optic lines.

"Electrons can easily make an L-shaped turn because the wavelengths in which they operate are small," said Zhang."Light wavelengths are generally bigger, so they need more space to maneuver. It's like turning a long, stretch limo instead of a motorcycle around a corner. That's why optics require bulky mirrors to control their movements. Scaling down the optical device also makes it faster because the single atomic layer of graphene can significantly reduce the capacitance -- the ability to hold an electric charge -- which often hinders device speed."

Graphene-based modulators could overcome the space barrier of optical devices, the researchers said. They successfully shrunk a graphene-based optical modulator down to a relatively tiny 25 square microns, a size roughly 400 times smaller than a human hair. The footprint of a typical commercial modulator can be as large as a few square millimeters.

Even at such a small size, graphene packs a punch in bandwidth capability. Graphene can absorb a broad spectrum of light, ranging over thousands of nanometers from ultraviolet to infrared wavelengths. This allows graphene to carry more data than current state-of-the-art modulators, which operate at a bandwidth of up to 10 nanometers, the researchers said.

"Graphene-based modulators not only offer an increase in modulation speed, they can enable greater amounts of data packed into each pulse," said Zhang."Instead of broadband, we will have 'extremeband.' What we see here and going forward with graphene-based modulators are tremendous improvements, not only in consumer electronics, but in any field that is now limited by data transmission speeds, including bioinformatics and weather forecasting. We hope to see industrial applications of this new device in the next few years."

Other UC Berkeley co-authors of this paper are graduate student Erick Ulin-Avila and post-doctoral researcher Thomas Zentgraf in Zhang's lab; and visiting scholar Baisong Geng and graduate student Long Ju in Wang's lab.

This work was supported through the Center for Scalable and Integrated Nano-Manufacturing (SINAM), an NSF Nanoscale Science and Engineering Center. Funding from the Department of Energy's Basic Energy Science program at Lawrence Berkeley National Laboratory also helped support this research.

Source

Scientists Achieve Guiding of Electrons by Purely Electric Fields

The research is published online inPhysical Review Letters.

This new technique of electron guiding -- which resembles the guiding of light waves in optical fibres -- promises a variety of applications, from guided matter-wave experiments to non-invasive electron microscopy.

Electrons have been the first elementary particles revealing their wave-like properties and have therefore been of great importance in the development of the theory of quantum mechanics. Even now the observation of electrons leads to new insight into the fundamental laws of physics. Measurements involving confined electrons have so far mainly been performed in so-called Penning traps, which combine a static magnetic field with an oscillating electric field.

For a number of experiments with propagating electrons, like interferometry with slow electrons, it would be advantageous to confine the electrons by a purely electric field. This can be done in an alternating quadrupole potential similar to the standard technique that is used for ion trapping. These so-called Paul traps are based on four electrodes to which a radiofrequency voltage is applied. The resulting field evokes a driving force which keeps the particle in the centre of the trap. Wolfgang Paul received the Nobel Prize in physics for the invention of these traps in 1989.

For several years by now scientists realize Paul traps with micro structured electrodes on planar substrates, using standard microelectronic chip technology. Dr. Hommelhoff and his group have now applied this method for the first time to electrons. Since the mass of these point-like particles is only a tenth of a thousandth of the mass of an ion, electrons react much faster to electric fields than the rather heavy ions. Hence, in order to guide electrons, the frequency of the alternating voltage applied to the electrodes has to be much higher than for the confinement of ions and is in the microwave range, at around 1 GHz.

In the experiment electrons are generated in a thermal source (in which a tungsten wire is heated like in a light bulb) and the emitted electrons are collimated to a parallel beam of a few electron volts. From there the electrons are injected into the"wave-guide." It is being generated by five electrodes on a planar substrate to which an alternating voltage with a frequency of about 1 GHz is applied. This introduces an oscillating quadrupole field in a distance of half a millimetre above the electrodes, which confines the electrons in the radial direction. In the longitudinal direction there is no force acting on the particles so that they are free to travel along the"guide tube." As the confinement in the radial direction is very strong the electrons are forced to follow even small directional changes of the electrodes.

In order to make this effect more visible the 37mm long electrodes are bent to a curve of 30 degrees opening angle and with a bending radius of 40mm. At the end of the structure the guided electrons are ejected and registered by a detector. A bright spot caused by guided electrons appears on the detector right at the exit of the guide tube, which is situated in the left part of the picture. When the alternating field is switched off a more diffusively illuminated area shows up on the right side. It is caused by electrons spreading out from the source and propagating on straight trajectories over the substrate.

"With this fundamental experiment we were able to show that electrons can be efficiently guided be purely electric fields," says Dr. Hommelhoff."However, as our electron source yields a rather poorly collimated electron beam we still lose many electrons." In the future the researchers plan to combine the new microwave guide with an electron source based on field emission from an atomically sharp metal tip. These devices deliver electron beams with such a strong collimation that their transverse component is limited by the Heisenberg uncertainty principle only.

Under these conditions it should be feasible to investigate the individual quantum mechanical oscillations of the electrons in the radial potential of the guide."The strong confinement of electrons observed in our experiment means that a"jump" from one quantum state to the neighbouring higher state requires a lot of energy and is therefore not very likely to happen," explains Johannes Hoffrogge, doctoral student at the experiment."Once a single quantum state is populated it will remain so for an extended period of time and can be used for quantum experiments." This would make it possible to conduct quantum physics experiments such as interferometry with guided slow electrons. Here the wave function of an electron is first split up; later on, its two components are brought together again whereby characteristic superpositions of quantum states of the electron can be generated. But the new method could also be applied for a new form of electron microscopy.

Source

What Electric Car Convenience Is Worth

Results of one study show the electric car attributes that are most important for consumers: driving range, fuel cost savings and charging time. The results are based on a national survey conducted by the researchers, UD professors George Parsons, Willett Kempton and Meryl Gardner, and Michael Hidrue, who recently graduated from UD with a doctoral degree in economics. Lead author Hidrue conducted the research for his dissertation.

The study, which surveyed more than 3,000 people, showed what individuals would be willing to pay for various electric vehicle attributes. For example, as battery charging time decreases from 10 hours to five hours for a 50-mile charge, consumers' willingness to pay is about$427 per hour in reduction time. Drop charging time from five hours to one hour, and consumers would pay an estimated$930 an hour. Decrease the time from one hour to 10 minutes, and they would pay$3,250 per hour.

For driving range, consumers value each additional mile of range at about$75 per mile up to 200 miles, and$35 a mile from 200-300 miles. So, for example, if an electric vehicle has a range of 200 miles and an otherwise equivalent gasoline vehicle has a range of 300, people would require a price discount of about$3,500 for the electric version. That assumes everything else about the vehicle is the same, and clearly there is lower fuel cost with an electric vehicle and often better performance. So all the attributes have to be accounted for in the final analysis of any car.

"This information tells the car manufacturers what people are willing to pay for another unit of distance," Parsons said."It gives them guidance as to what cost levels they need to attain to make the cars competitive in the market."

The researchers found that battery costs would need to decrease substantially without subsidy and with current gas prices for electric cars to become competitive in the market. However, the researchers said, the current$7,500 government tax credit could bridge the gap between electric car costs and consumers' willingness to pay if battery costs decline to$300 a kilowatt hour, the projected 2014 cost level by the Department of Energy. Many analysts believe that goal is within reach.

The team's analysis could also help guide automakers' marketing efforts -- it showed that an individual's likelihood of buying an electric vehicle increases with characteristics such as youth, education and an environmental lifestyle. Income was not important.

In a second recently published study, UD researchers looked at electric vehicle driving range using second-by-second driving records. That study, which is based on a year of driving data from nearly 500 instrumented gasoline vehicles, showed that 9 percent of the vehicles never exceeded 100 miles in a day. For those who are willing to make adaptations six times a year -- borrow a gasoline car, for example -- the 100-mile range would work for 32 percent of drivers.

"It appears that even modest electric vehicles with today's limited battery range, if marketed correctly to segments with appropriate driving behavior, comprise a large enough market for substantial vehicle sales," the authors concluded.

Kempton, who published the driving patterns article with UD marine policy graduate student Nathaniel Pearre and colleagues at the Georgia Institute of Technology, pointed out that U.S. car sales are around 12 million in an average, non-recession year. Nine percent of that would be a million cars per year -- for comparison to current production, for example, Chevy plans to manufacture just 10,000 Volts in 2011.

By this measure, the potential market would justify many more plug-in cars than are currently being produced, Kempton said.

The findings of the two studies were reported online in March and February inResource and Energy EconomicsandTransportation Research, respectively.

Source

Pairing Quantum Dots With Fullerenes for Nanoscale Photovoltaics

"This is the first demonstration of a hybrid inorganic/organic, dimeric (two-particle) material that acts as an electron donor-bridge-acceptor system for converting light to electrical current," said Brookhaven physical chemist Mircea Cotlet, lead author of a paper describing the dimers and their assembly method inAngewandte Chemie.

By varying the length of the linker molecules and the size of the quantum dots, the scientists can control the rate and the magnitude of fluctuations in light-induced electron transfer at the level of the individual dimer."This control makes these dimers promising power-generating units for molecular electronics or more efficient photovoltaic solar cells," said Cotlet, who conducted this research with materials scientist Zhihua Xu at Brookhaven's Center for Functional Nanomaterials (CFN).

Scientists seeking to develop molecular electronics have been very interested in organic donor-bridge-acceptor systems because they have a wide range of charge transport mechanisms and because their charge-transfer properties can be controlled by varying their chemistry. Recently, quantum dots have been combined with electron-accepting materials such as dyes, fullerenes, and titanium oxide to produce dye-sensitized and hybrid solar cells in the hope that the light-absorbing and size-dependent emission properties of quantum dots would boost the efficiency of such devices. But so far, the power conversion rates of these systems have remained quite low.

"Efforts to understand the processes involved so as to engineer improved systems have generally looked at averaged behavior in blended or layer-by-layer structures rather than the response of individual, well-controlled hybrid donor-acceptor architectures," said Xu.

The precision fabrication method developed by the Brookhaven scientists allows them to carefully control particle size and interparticle distance so they can explore conditions for light-induced electron transfer between individual quantum dots and electron-accepting fullerenes at the single molecule level.

The entire assembly process takes place on a surface and in a stepwise fashion to limit the interactions of the components (particles), which could otherwise combine in a number of ways if assembled by solution-based methods. This surface-based assembly also achieves controlled, one-to-one nanoparticle pairing.

To identify the optimal architectural arrangement for the particles, the scientists strategically varied the size of the quantum dots -- which absorb and emit light at different frequencies according to their size -- and the length of the bridge molecules connecting the nanoparticles. For each arrangement, they measured the electron transfer rate using single molecule spectroscopy.

"This method removes ensemble averaging and reveals a system's heterogeneity -- for example fluctuating electron transfer rates -- which is something that conventional spectroscopic methods cannot always do," Cotlet said.

The scientists found that reducing quantum dot size and the length of the linker molecules led to enhancements in the electron transfer rate and suppression of electron transfer fluctuations.

"This suppression of electron transfer fluctuation in dimers with smaller quantum dot size leads to a stable charge generation rate, which can have a positive impact on the application of these dimers in molecular electronics, including potentially in miniature and large-area photovoltaics," Cotlet said.

"Studying the charge separation and recombination processes in these simplified and well-controlled dimer structures helps us to understand the more complicated photon-to-electron conversion processes in large-area solar cells, and eventually improve their photovoltaic efficiency," Xu added.

A U.S. patent application is pending on the method and the materials resulting from using the technique, and the technology is available for licensing. This work was funded by the DOE Office of Science.

Source

Successful First Test Drive of 'Sighted' Wheelchair

The wheelchair has a joystick for steering and a haptic robot that acts as a virtual white cane. With the help of a laser scanner a simplified 3D map is created of the wheelchair surroundings. The laser scanner uses Time-of-flight technique. The 3D map is transferred to the haptic robot so that a visually impaired wheelchair driver can"feel or see" obstacles such as open doors or oncoming people, and navigate past them.

The"sighted" wheelchair has been developed by Kalevi Hyyppä, a professor at Luleå University of Technology and his research team at the LTU division EISLAB. The other members of the research team are prospective Ph.D. student Daniel Innala Ahlmark, assistant professor Håkan Fredriksson and Ph.D. student Fredrik Broström.

"This may be important aids for the visually impaired who are wheelchair users. Many have already been in touch with me and asked if they can come for a test drive," says Kalevi Hyyppä.

The first test of the"sighted" wheelchair for an audience was carried out in one of the corridors of the Department of Computer Science, Electrical- and Space Engineering at Luleå University of Technology.

There are several classrooms in the corridor, which means that students often pass there. For those who are visually impaired or blind, it is quite a changing environment to move in. Daniel Innala Ahlmark, who is visually impaired, dared to test the wheelchair while explaining how he experienced it -- and he did so before the entire local and even national media in Sweden.

"I feel safe when I run it, it is like using a white cane," he said as he avoided various obstacles along the corridor.

There is much left when it comes to improving the 3D sensor and the haptic robot. The laser beam that sweeps in front of the wheelchair hits only objects which are a certain height. It has not the capacity to see things that are higher or lower than that height. Now the research team plan to develop a 3D camera that can do a full 3D measurement. Then the sighted wheelchair can be manufactured and used for real. This might be possible in approximately five years.

Research on the sighted wheelchair has been made with funding from the European Regional Structural Fund Northern Sweden.

Source

Super Energy Storage: Activated Graphene Makes Superior Supercapacitors for Energy Storage

"Those properties make this new form of carbon particularly attractive for meeting electrical energy storage needs that also require a quick release of energy -- for instance, in electric vehicles or to smooth out power availability from intermittent energy sources, such as wind and solar power," said Brookhaven materials scientist Eric Stach, a co-author on a paper describing the material published inScienceon May 12, 2011.

Supercapacitors are similar to batteries in that both store electric charge. Batteries do so through chemical reactions between metallic electrodes and a liquid electrolyte. Because these chemicals take time to react, energy is stored and released relatively slowly. But batteries can store a lot of energy and release it over a fairly long time.

Supercapacitors, on the other hand, store charge in the form of ions on the surface of the electrodes, similar to static electricity, rather than relying on chemical reactions. Charging the electrodes causes ions in the electrolyte to separate, or polarize, as well -- so charge gets stored at the interface between the electrodes and the electrolyte. Pores in the electrode increase the surface area over which the electrolyte can flow and interact -- increasing the amount of energy that can be stored.

But because most supercapacitors can't hold nearly as much charge as batteries, their use has been limited to applications where smaller amounts of energy are needed quickly, or where long life cycle is essential, such as in mobile electronic devices.

The new material developed by the UT-Austin researchers may change that. Supercapacitors made from it have an energy-storage capacity, or energy density, that is approaching the energy density of lead-acid batteries, while retaining the high power density -- that is, rapid energy release -- that is characteristic of supercapacitors.

"This new material combines the attributes of both electrical storage systems," said University of Texas team leader Rodney Ruoff."We were rather stunned by its exceptional performance."

The UT-Austin team had set out to create a more porous form of carbon by using potassium hydroxide to restructure chemically modified graphene platelets -- a form of carbon where the atoms are arrayed in tile-like rings laying flat to form single-atom-thick sheets. Such"chemical activation" has been previously used to create various forms of"activated carbon," which have pores that increase surface area and are used in filters and other applications, including supercapacitors.

But because this new form of carbon was so superior to others used in supercapacitors, the UT-Austin researchers knew they'd need to characterize its structure at the nanoscale.

Ruoff had formed a hypothesis that the material consisted of a continuous three-dimensional porous network with single-atom-thick walls, with a significant fraction being"negative curvature carbon," similar to inside-out buckyballs. He turned to Stach at Brookhaven for help with further structural characterization to verify or refute this hypothesis.

Stach and Brookhaven colleague Dong Su conducted a wide range of studies at the Lab's Center for Functional Nanomaterials, the National Synchrotron Light Source, and at the National Center for Electron Microscopy at Lawrence Berkeley National Laboratory, all three facilities supported by the DOE Office of Science."At the DOE laboratories, we have the highest resolution microscopes in the world, so we really went full bore into characterizing the atomic structure," Stach said.

"Our studies revealed that Ruoff's hypothesis was in fact correct, and that the material's three-dimensional nanoscale structure consists of a network of highly curved, single-atom-thick walls forming tiny pores with widths ranging from 1 to 5 nanometers, or billionths of a meter."

The study includes detailed images of the fine pore structure and the carbon walls themselves, as well as images that show how these details fit into the big picture."The data from NSLS were crucial to showing that our highly local characterization was representative of the overall material," Stach said.

"We're still working with Ruoff and his team to pull together a complete description of the material structure. We're also adding computational studies to help us understand how this three-dimensional network forms, so that we can potentially tailor the pore sizes to be optimal for specific applications, including capacitive storage, catalysis, and fuel cells," Stach said.

Meanwhile, the scientists say the processing techniques used to create the new form of carbon are readily scalable to industrial production."This material -- being so easily manufactured from one of the most abundant elements in the universe -- will have a broad range impacts on research and technology in both energy storage and energy conversion," Ruoff said.

Source

Toward Faster Transistors: Physicists Discover Physical Phenomenon That Could Boost Computers' Clock Speed

In this week's issue of the journalScience,MIT researchers and their colleagues at the University of Augsburg in Germany report the discovery of a new physical phenomenon that could yield transistors with greatly enhanced capacitance -- a measure of the voltage required to move a charge. And that, in turn, could lead to the revival of clock speed as the measure of a computer's power.

In today's computer chips, transistors are made from semiconductors, such as silicon. Each transistor includes an electrode called the gate; applying a voltage to the gate causes electrons to accumulate underneath it. The electrons constitute a channel through which an electrical current can pass, turning the semiconductor into a conductor.

Capacitance measures how much charge accumulates below the gate for a given voltage. The power that a chip consumes, and the heat it gives off, are roughly proportional to the square of the gate's operating voltage. So lowering the voltage could drastically reduce the heat, creating new room to crank up the clock.

MIT Professor of Physics Raymond Ashoori and Lu Li, a postdoc and Pappalardo Fellow in his lab -- together with Christoph Richter, Stefan Paetel, Thilo Kopp and Jochen Mannhart of the University of Augsburg -- investigated the unusual physical system that results when lanthanum aluminate is grown on top of strontium titanate. Lanthanum aluminate consists of alternating layers of lanthanum oxide and aluminum oxide. The lanthanum-based layers have a slight positive charge; the aluminum-based layers, a slight negative charge. The result is a series of electric fields that all add up in the same direction, creating an electric potential between the top and bottom of the material.

Ordinarily, both lanthanum aluminate and strontium titanate are excellent insulators, meaning that they don't conduct electrical current. But physicists had speculated that if the lanthanum aluminate gets thick enough, its electrical potential would increase to the point that some electrons would have to move from the top of the material to the bottom, to prevent what's called a"polarization catastrophe." The result is a conductive channel at the juncture with the strontium titanate -- much like the one that forms when a transistor is switched on. So Ashoori and his collaborators decided to measure the capacitance between that channel and a gate electrode on top of the lanthanum aluminate.

They were amazed by what they found: Although their results were somewhat limited by their experimental apparatus, it may be that an infinitesimal change in voltage will cause a large amount of charge to enter the channel between the two materials."The channel may suck in charge -- shoomp! Like a vacuum," Ashoori says."And it operates at room temperature, which is the thing that really stunned us."

Indeed, the material's capacitance is so high that the researchers don't believe it can be explained by existing physics."We've seen the same kind of thing in semiconductors," Ashoori says,"but that was a very pure sample, and the effect was very small. This is a super-dirty sample and a super-big effect." It's still not clear, Ashoori says, just why the effect is so big:"It could be a new quantum-mechanical effect or some unknown physics of the material."

There is one drawback to the system that the researchers investigated: While a lot of charge will move into the channel between materials with a slight change in voltage, it moves slowly -- much too slowly for the type of high-frequency switching that takes place in computer chips. That could be because the samples of the material are, as Ashoori says,"super dirty"; purer samples might exhibit less electrical resistance. But it's also possible that, if researchers can understand the physical phenomena underlying the material's remarkable capacitance, they may be able to reproduce them in more practical materials.

Triscone cautions that wholesale changes to the way computer chips are manufactured will inevitably face resistance."So much money has been injected into the semiconductor industry for decades that to do something new, you need a really disruptive technology," he says.

"It's not going to revolutionize electronics tomorrow," Ashoori agrees."But this mechanism exists, and once we know it exists, if we can understand what it is, we can try to engineer it."

Source

Lasers Take the Lead in Auto Manufacturing

The era of gas guzzlers that clatter through streets and pollute the air is over. Cars rolling off the assembly line today are cleaner, quieter and -- in terms of their performance weight -- more efficient than ever before. Nevertheless, development continues. Ever-stricter environmental regulations and steadily rising fuel costs are increasing the demand for cars that further reduce their impact on the environment. But customer demands are often tough for manufacturers to meet: car bodies should be safe yet light-weight and engines durable yet efficient. Year after year, new models must be developed and built that can claim to be better, more efficient, and more intelligent than the last.

The race against time and competitors places high demands on manufacturers and their suppliers. Lasers can help them win the race. Resistant to wear and universally applicable, laser light is an ideal tool in the manufacture of vehicles. Lasers can be used to join, drill, structure, cut or shape any kind of material. Surfaces can be engineered for motors and drive trains that create less friction and use less fuel. Lasers are not only a decisive key towards faster, more efficient and economical production, but also towards energy-saving vehicles. At Laser 2011, Fraunhofer scientists will demonstrate how we can use lasers to save time, money and energy.

A weight-loss program in automotive manufacturing

Extra pounds cost energy. They have to be accelerated and slowed down every time you drive -- over the entire lifespan of the car. To reduce weight, manufacturers are increasingly turning to the use of fiber-reinforced plastics, which are 30 to 50 percent lighter than metal. The disadvantage, however, is that these new materials are difficult to process. Fiber-reinforced plastics are brittle, meaning cutting and drilling tools are quickly worn out and the conventional assembly techniques used for metal components are often not appropriate."Lasers represent an ideal alternative here," explains Dr. Arnold Gillner of the Fraunhofer Institute for Laser Technology ILT in Aachen."Lasers can cut fiber-reinforced plastics without wear and can join them too. With the appropriate lasers, we can cut and ablate components with minimal thermal side-effects. Lasers can also be used for welding light-weight components -- a viable alternative to conventional bonding technology. We can even join fiber-reinforced plastics to metals with laser welding. The laser roughens the metal surface, while the plastic, briefly-heated, penetrates the pores of the metal and hardens. The results are very stable."

Weight reduction can also be achieved with high-strength metallic materials. These, however, are difficult to process."Joining combinations of various materials allows us to make optimal use of the individual materials' specific properties. But this proves to be difficult in many cases," explains Dr. Anja Techel, Deputy Director of the Fraunhofer Institute for Material and Beam Technology IWS in Dresden. Her team believes in lasers:"With our newly-developed integrated laser tools, we can now even weld together combinations of materials, free of fissures or cracks." At Laser 2011, Fraunhofer scientists will present, for the first time, a new welding head capable not only of focusing with extreme precision but of moving back and forth across the seam with high frequency to mix the molten materials. When they harden, they create a stable bond.

Laser replaces chemistry

Lasers also save time and money in tool design. The molds used in the production of plastic fixtures and steering wheels, for example, have to be structured to give the finished component a visually and tactilely appealing surface. Most car manufacturers order a design from their suppliers, whose surface typically has the appearance of leather. Until now, the negative pattern used to create the design has been etched out of the steel tools used in injection molding -- a tedious and time-consuming process."With lasers, the steel surface can not only be patterned more quickly, but also with greater scope for variety," explains Kristian Arntz of the Fraunhofer Institute for Production Technology IPT."We can transfer any possible design directly from the CAD model to the tool surface: What will later become a groove in the plastic is preserved as a ridge, while the surrounding material is vaporized. The process is efficient, fully automatic, and highly variable."

Saving energy with low friction motors

Laser technology is also in demand in engine optimization. Engineers strive to keep friction as low as possible in order to improve efficiency."That is true not only for the electric engines currently being developed, but also for classic internal combustion engines and diesel motors, as well as transmissions and bearings," says Arnold Gillner of the ILT. Ceramic, high-performance coatings are especially desirable, because they are not only resistant to wear but also smooth, which generates less friction. Coated metal components have until now been prohibitively expensive, being produced in plasma chambers in which the ceramic was vaporized and applied to the surface of the components. Fraunhofer scientists have now developed a less expensive and faster method in which work pieces are coated with ceramic nano-particles, then treated with a laser. This finishing process has already been applied to gear wheels and bearings.

Lasers can even be used to make specific modifications to the properties of engine parts."Friction between the cylinder wall and piston is responsible for a big part of a motor's energy consumption. That is why we try to minimize it. This is especially important for engines featuring modern, automatic start-stop functions that are stressed by frequent ignition," says Gillner."To protect them, we have to ensure that the cylinder is always coated with a film of oil. Laser technology can help reduce friction with special structuring processes that improve oil adhesion." Fraunhofer researchers aim to increase the engine's life-span and reduce energy consumption in this way.

Fitness program for electric cars

Lasers can even increase the efficiency and life-span of electric batteries. That is good news for manufacturers and owners of electric cars, since batteries continue to be extremely expensive. The engineers and scientists at Fraunhofer are currently working on various solutions to make batteries more durable and less expensive. One approach is to increase the surface area of the electrodes with appropriate coating in order to increase their efficiency. Another approach involves analyzing and optimizing production processes.

Manufacturers produce batteries using one anode and one cathode cell, which they then connect. In theory that sounds pretty simple, but in practice the fusing of copper anodes with aluminum cathodes creates brittle connections that break easily. That presents a problem for application in cars that sometimes drive on cobblestone or dirt roads. With the help of lasers, researchers at the ILT have succeeded in forming durable connections between electrodes without creating the culprit brittle alloys. Researchers at the IWS in Dresden have developed an alternative solution in which a laser warms the surfaces and rollers press them together."Using roll plating with lasers and inductive pre-heating, we were able to create very stable connections with high electrical conductivity, with only a minimal loss of power," reports Anja Techel."The finished batteries are very efficient. And since only small amounts of electrical energy are transformed into heat, these batteries do not require as much cooling."

Source

Finding Reserves on the Electrical Grid

When storms lash northern and eastern Germany, it regularly gets tight in the high-voltage and highest-voltage electrical grids. Electricity from renewable resources has priority on the grid. But, on stormy days in particular, wind turbine systems must be taken offline, because the gird capacities are insufficient."Currently we are in a situation where we have high inflows from renewable energies into our high voltage line system and are expecting large increases in the future. However, the grid is not designed for this level of energy feed," reports Hanjo During of envia Verteilnetz GmbH in Halle, Germany, Additional power lines are being planned. But the authorization processes could take years and very often fail due to the resistance of the people living near the projected path of the lines.

For this reason, the grid operators are already utilizing various line-monitoring procedures to increase the grid capacity over the short term: They utilize reserves that are the result of a standardized assumption regarding the worst weather conditions for operating the line and the actual state of the line. In favorable weather conditions, they were therefore able to increase the transmission capacities by 20 percent or more. Currently, Amprion and envia Verteilnetz are testing a new type of autonomously powered sensor network to monitor 110 kV and 380 kV lines. It is being developed jointly with the Fraunhofer Institutes for Reliability and Microintegration IZM in Berlin and Electronic Nanosystems ENAS in Chemnitz, Germany as well as other research and industrial partners in the"ASTROSE" project."Our autonomously powered sensor network can be retrofitted easily and does not require additional infrastructure," says Dr. -Ing. Volker Großer from the IZM. In contrast to the current monitoring systems it supplies measurement data from a tight-knit sensor network directly attached to the conductor wires.

How much current can be transmitted by a power line depends very much on temperature. If the conductor wires heat up as a result of flowing current or the sun, they expand and sag. If the sagging conductor wire gets too close to the ground, buildings, vehicles or humans, there is a risk of electrocution. To rule this out, prescribed safety clearances are mandatory. At the same time, the permitted current flow is calculated under the assumption that the ambient temperature is 35°C and that the wind's velocity will not exceed 0.6 m/s. However, high midsummer temperatures often bring with them a lull in the wind. Most wind turbine systems will only start to operate once wind velocity has reached 3 m/s. They deliver high amounts of electricity during fall and in winter when the power lines are effectively cooled by the weather.

To better utilize these reserves in the grid without compromising safety, the ASTROSE project partners equip the 110 kV and 380 kV lines with„eGrains." Cylindrical sensor nodes are wrapped around the conductor wire approximately every 500 meters.„They consist of two half cups that are clamped on and attached to each other. The ASTROSE-eGrains measure the cable's angle of inclination, the current flow, the temperature as well as wind movement. All measurement values are relayed from eGrain to eGrain to the next transformer station and there they are fed into the central monitoring and control system or rather made available to the internet-based remote maintenance systems of the grid operators," explains Großer. The ASTROSE eGrains pull the energy they require from the electrical field that surrounds the conductor wires. However, the ASTROSE sensor network does not only help utilize the capacities of the power lines better. It also reports dangerous line sags, such as can occur in winter as a result of ice build-up on the lines. The sensor node can be seen at the„Sensor + Test" tradeshow from June 7 -- 9 in Nuremberg, Germany, in Hall 12, Booth 231.

Source

Electromechanics Also Operates at the Nanoscale

"We have been studying carbon nanotubes theoretically, in order to see how they behave when they are stimulated to behave according to the laws quantum mechanics. The results provide a completely new platform for scientists to stand on," says Gustav Sonne of the Department of Physics at the University of Gothenburg.

Every day we use a number of different microelectromechanical components for various forms of detection, to determine whether a certain process has taken place or whether a certain substance is present. These cannot be detected without instruments. One example is the detection of rapid accelerations that is used to activate the airbag in a car during an accident. What all of these components have in common is that they combine mechanical and electronic properties in order to react to external stimuli.

Gustav Sonne has taken research down to a whole new dimension -- from the micrometer scale to the nanometer scale -- and he has studied the younger brothers of these components: nanoelectromechanical systems. The studies have been based on tiny nanotubes suspended between two electrical contacts. He has subsequently calculated how small vibrations in the suspended tubes can be coupled to a current that is led through them.

"Our research has focussed mainly on how these systems, which consist of a tiny, super-light mechanical oscillator (the suspended nanotube), can be described in quantum mechanical terms, and what effects this has on the measurements we can carry out. We have been able to demonstrate a number of new mechanisms for electromechanical coupling that should be possible to observe experimentally. This, in turn, may lead to extremely exotic physical phenomena in these structures, phenomena which may be of interest for research into quantum computers, and other fields."

Interest in nanotubes is based on their outstanding properties: they are among the strongest materials known, weigh next to nothing, and have extremely high conductivity for both electric currents and heat. Carbon nanotubes can be used to manufacture composite materials that are several orders of magnitude stronger than currently available materials.

The thesis"Mesoscopic phenomena in the electromechanics of suspended nanowires" was successfully defended in the Department of Physics. Supervisor: Associate professor Leonid Gorelik.

Source

Battery-Less Chemical Detector Developed

The device overcomes the power requirement of traditional sensors and is simple, highly sensitive and can detect various molecules quickly. Its development could be the first step in making an easily deployable chemical sensor for the battlefield.

The Lab's Yinmin"Morris" Wang and colleagues Daniel Aberg, Paul Erhart, Nipun Misra, Aleksandr Noy and Alex Hamza, along with collaborators from the University of Shanghai for Science and Technology, have fabricated the first-generation battery-less detectors that use one-dimensional semiconductor nanowires.

The nanosensors take advantage of a unique interaction between chemical species and semiconductor nanowire surfaces that stimulate an electrical charge between the two ends of nanowires or between the exposed and unexposed nanowires.

The group tested the battery-less sensors with different types of platforms -- zinc-oxide and silicon -- using ethanol solvent as a testing agent.

In the zinc-oxide sensor the team found there was a change in the electric voltage between the two ends of nanowires when a small amount of ethanol was placed on the detector.

"The rise of the electric signal is almost instantaneous and decays slowly as the ethanol evaporates," Wang said.

However, when the team placed a small amount of a hexane solvent on the device, little electric voltage was seen,"indicating that the nanosensor selectively responds to different types of solvent molecules," Wang said.

The team used more than 15 different types of organic solvents and saw different voltages for each solvent."This trait makes it possible for our nanosensors to detect different types of chemical species and their concentration levels," Wang said.

The response to different solvents was somewhat similar when the team tested the silicon nanosensors. However, the voltage decay as the solvent evaporated was drastically different from the zinc-oxide sensors."The results indicate that it is possible to extend the battery-less sensing platform to randomly aligned semiconductor nanowire systems," Wang said.

The team's next step is to test the sensors with more complex molecules such as those from explosives and biological systems.

The research appears on the inside front cover of the Jan. 4 issue ofAdvanced Materials.

Source

NASA Building Instrument to Study Magnetic Reconnection

Several spacecraft have already sent back tantalizing data when they happened to witness a magnetic reconnection event in Earth's magnetosphere. However, there are no spacecraft currently dedicated to the study of this phenomenon.

All this will change in 2014 when NASA launches the Magnetospheric Multiscale (MMS) mission, a fleet of four identical spacecraft that will focus exclusively on this dynamic magnetic system that stretches from the sun to Earth and beyond.

At NASA's Goddard Space Flight Center in Greenbelt, Md., a team of scientists and engineers are working on a crucial element of the MMS instrument suite: the Fast Plasma Instrument (FPI). Some 100 times faster than any previous similar instrument, the FPI will collect a full sky map of data at the rate of 30 times per second -- a necessary speed given that MMS will only travel through the reconnection site for under a second.

"Imagine flying by a tiny object on an airplane very rapidly," says Craig Pollock, the Co-Investigator for FPI at Goddard."You want to capture a good picture of it, but you don't get to just walk around it and take your time snapping photos from different angles. You have to grab a quick shot as you're passing. That's the challenge."

Previous spacecraft, such as Cluster and THEMIS have helped narrow down the regions near Earth where magnetic reconnection happens. The solar wind streams towards Earth until it hits our planet's magnetic field, says Tom Moore, the project scientist for MMS at Goddard."The solar wind comes flying in and the terrestrial stuff is like molasses -- slow, cold and reluctant to do whatever the solar wind wants. So there is a contest of wills whenever the two fields connect up via reconnection."

That's what happens on the sun side of Earth. On the other side, the night side, magnetic reconnection in Earth's magnetic tail causes a geometry change in the shape of the field lines. Portions of the magnetic field get disconnected from the rest of the tail and shoot away from Earth.

The orbit for MMS will be tailored to hit these spots of magnetic reconnection on a regular basis. The first year and a half will be spent in the day side and the last six months in the night side. In the case of both day- and night-side reconnection, the changing magnetic fields also send the local ionized gas, or plasma, off with a great push. Measuring that plasma -- a concrete, physical entity unlike the more abstract magnetic fields themselves -- is one way to learn more about what's happening in that process.

"Right now the state of reconnection knowledge is simply that we know it's going on," says Moore."One of the fundamental questions is to figure out what controls the process -- the little stuff deep inside or the larger, external, boundary conditions. Some conditions produce a small burst of energy and sometimes, during what we think are the same external conditions, there's a huge burst of energy. That might be explained if the reconnection event depended crucially on what's going on deep inside, in an area we've never been able to see before."

The FPI instrument will measure the plasma in these small regions using electron and ion spectrometers. In order to capture as much as possible in the second-long journey through a magnetic reconnection site, each detector will be made of two spectrometers whose field of view is separated by 45 degrees, each of which can scan through a 45-degree arc for a larger panorama. There will be four dual electron spectrometers and four dual ion spectrometers onboard each MMS spacecraft. In combination, the ion spectrometers will produce a three-dimensional picture of the ion plasma every 150 milliseconds, while the electron spectrometers will do the same for the electrons every 30 milliseconds.

Not only is this approach an improvement of 100 times over previous plasma data collection, it's an advancement in terms of instrument building. For those doing the math: there are four plus four instruments plus one data processing unit on each of four spacecraft, which equates to 32 sensors and four data processing units, 36 boxes total.

"That's a huge number," says Pollock."We're used to delivering one box, or occasionally two or three."

These instruments are, in turn, just part of the 100 instruments being built for MMS, each tailored to measure various electric and magnetic signals in space. The production is made even more challenging, says Karen Halterman, the program manager for MMS who oversees all pre-launch activities of the mission, because the entire spacecraft must be created to exacting standards."You can't have a satellite that produces its own large electromagnetic signature when you're trying to precisely measure electromagnetism outside the satellite," she says."We can't even use standard metal tools to build the hundreds of pieces in each satellite since they will add magnetic signatures into spacecraft."

The Southwest Research Institute in San Antonio, who designed the original instrument suite, is overseeing all the instruments for MMS, which are being built all over the country and globe -- including in Japan. A Japanese company called Meisei has been contracted to build the ion spectrometers for the FPI.

"In the middle of a huge catastrophe," says Pollock,"the (Japanese) response has been remarkable and admirable. They have their problems, not least of which is rolling blackouts when some of the upcoming tests will require achieving vacuums that need several days of continuous electricity. We came up with a lot of contingency plans, but it turns out they don't need much help."

The Japanese instruments are still on track. The engineering test unit of the ion spectrometers is scheduled to arrive at Goddard -- after testing is completed at Japan's Institute of Space and Astronautical Science and NASA's Marshall Space Flight Center in Huntsville, Ala. -- early this summer. Indeed, the first FPI instrument for the first MMS spacecraft is due to arrive at the Southwest Research Institute in March of 2012.

Naturally, it's a busy time. The FPI team is finalizing the hardware and making sure all the parts pass a variety of standard tests, from ensuring the instrument won't vibrate apart during launch to making sure they still function properly when placed next to the electromagnetic signals streaming out from other instruments.

"What MMS is looking for is not something visible," says Halterman."If you have a mission to study the sun or Jupiter, you can look at a picture and see the sun or Jupiter. Magnetic reconnection is a fundamental physics process. It happens on stars, on the sun, all over the universe, but it's much harder to get a deep understanding of it. FPI and the rest of the MMS instrument suite, with their great improvement in speed and resolution, are going to help change that."

Source

New Way to Control Conductivity: Reversible Control of Electrical and Thermal Properties Could Find Uses in Storage Systems

"It's a new way of changing and controlling the properties" of materials -- in this case a class called percolated composite materials -- by controlling their temperature, says Gang Chen, MIT's Carl Richard Soderberg Professor of Power Engineering and director of the Pappalardo Micro and Nano Engineering Laboratories. Chen is the senior author of a paper describing the process that was published online on April 19 and will appear in a forthcoming issue ofNature Communications. The paper's lead authors are former MIT visiting scholars Ruiting Zheng of Beijing Normal University and Jinwei Gao of South China Normal University, along with current MIT graduate student Jianjian Wang. The research was partly supported by grants from the National Science Foundation.

The system Chen and his colleagues developed could be applied to many different materials for either thermal or electrical applications. The finding is so novel, Chen says, that the researchers hope some of their peers will respond with an immediate,"I have a use for that!"

One potential use of the new system, Chen explains, is for a fuse to protect electronic circuitry. In that application, the material would conduct electricity with little resistance under normal, room-temperature conditions. But if the circuit begins to heat up, that heat would increase the material's resistance, until at some threshold temperature it essentially blocks the flow, acting like a blown fuse. But then, instead of needing to be reset, as the circuit cools down the resistance decreases and the circuit automatically resumes its function.

Another possible application is for storing heat, such as from a solar thermal collector system, later using it to heat water or homes or to generate electricity. The system's much-improved thermal conductivity in the solid state helps it transfer heat.

Essentially, what the researchers did was suspend tiny flakes of one material in a liquid that, like water, forms crystals as it solidifies. For their initial experiments, they used flakes of graphite suspended in liquid hexadecane, but they showed the generality of their process by demonstrating the control of conductivity in other combinations of materials as well. The liquid used in this research has a melting point close to room temperature -- advantageous for operations near ambient conditions -- but the principle should be applicable for high-temperature use as well.

The process works because when the liquid freezes, the pressure of its forming crystal structure pushes the floating particles into closer contact, increasing their electrical and thermal conductance. When it melts, that pressure is relieved and the conductivity goes down. In their experiments, the researchers used a suspension that contained just 0.2 percent graphite flakes by volume. Such suspensions are remarkably stable: Particles remain suspended indefinitely in the liquid, as was shown by examining a container of the mixture three months after mixing.

By selecting different fluids and different materials suspended within that liquid, the critical temperature at which the change takes place can be adjusted at will, Chen says.

"Using phase change to control the conductivity of nanocomposites is a very clever idea," says Li Shi, a professor of mechanical engineering at the University of Texas at Austin. Shi adds that as far as he knows"this is the first report of this novel approach" to producing such a reversible system.

"I think this is a very crucial result," says Joseph Heremans, professor of physics and of mechanical and aerospace engineering at Ohio State University."Heat switches exist," but involve separate parts made of different materials, whereas"here we have a system with no macroscopic moving parts," he says."This is excellent work."

Source

Antibody-Based Biosensor Can Guide Environmental Clean-Ups, Provide Early Warning System for Spills

Testing of the biosensor in the Elizabeth River and Yorktown Creek, which both drain into lower Chesapeake Bay, shows that the instrument can process samples in less than 10 minutes, detect pollutants at levels as low as just a few parts per billion, and do so at a cost of just pennies per sample. Current technology requires hours of lab work, with a per-sample cost of up to$1,000.

"Our biosensor combines the power of the immune system with the sensitivity of cutting-edge electronics," says Dr. Mike Unger of VIMS."It holds great promise for real-time detection and monitoring of oil spills and other releases of contaminants into the marine environment."

The biosensor was developed and tested by Unger, fellow VIMS professor Steve Kaattari, and their doctoral student Candace Spier, with assistance from marine scientist George Vadas. The team's report of field tests with the sensor appears in this month's issue ofEnvironmental Toxicology and Chemistry.

The instrument was developed in conjunction with Sapidyne Instruments, Inc., with funding from the state of Virginia, the Office of Naval Research, and the Cooperative Institute for Coastal and Estuarine Environmental Technology, a partnership between NOAA and the University of New Hampshire.

The tests in the Elizabeth River took place during clean up of a site contaminated by polycyclic aromatic hydrocarbons (PAHs), byproducts of decades of industrial use of creosote to treat marine pilings. The U.S. Environmental Protection Agency considers PAHs highly toxic and lists 17 as suspected carcinogens.

The biosensor allowed the researchers to quantify PAH concentrations while the Elizabeth River remediation was taking place, gaining on-site knowledge about water quality surrounding the remediation site. Spier says the test was"the first use of an antibody-based biosensor to guide sampling efforts through near real-time evaluation of environmental contamination."

In the Yorktown Creek study, the researchers used the biosensor to track the runoff of PAHs from roadways and soils during a rainstorm.

Biosensor development

Kaattari says"Our basic idea was to fuse two different kinds of technologies -- monoclonal antibodies and electronic sensors -- in order to detect contaminants."

Antibodies are proteins produced by the immune system of humans and other mammals. They are particularly well suited for detecting contaminants because they have, as Kaattari puts it, an"almost an infinite power to recognize the 3-dimensional shape of any molecule."

Mammals produce antibodies that recognize and bind with large organic molecules such as proteins or with viruses. The VIMS team took this process one step further, linking proteins to PAHs and other contaminants, then exposing mice to these paired compounds in a manner very similar to a regular vaccination.

"Just like you get vaccinated against the flu, we in essence are vaccinating our mice against contaminants," says Kaattari."The mouse's lymphatic system then produces antibodies to PAHs, TNT, tributyl tin {TBT, the active ingredient in anti-fouling paints for boats}, or other compounds."

Once a mouse has produced an antibody to a particular contaminant, the VIMS team applies standard clinical techniques to produce"monoclonal antibodies" in sufficiently large quantities for use in a biosensor.

"This technology allows you to immortalize a lymphocyte that produces only a very specific antibody," says Kaattari."You grow the lymphocytes in culture and can produce large quantities of antibodies within a couple of weeks. You can preserve the antibody-producing lymphocyte forever, which means you don't have to go to a new animal every time you need to produce new antibodies."

From antibody to electrical signal

The team's next step was to develop a sensor that can recognize when an antibody binds with a contaminant and translate that recognition into an electrical signal. The Sapidyne^®sensor used by the VIMS team works via what Kaattari calls a"fluorescence-inhibitory, spectroscopic kind of assay."

In the sensor used on the Elizabeth River and Yorktown Creek, antibodies designed to recognize a specific class of PAHs were joined with a dye that glows when exposed to fluorescent light. The intensity of that light is in turn recorded as a voltage. The sensor also houses tiny plastic beads that are coated with what Spier calls a"PAH surrogate" -- a PAH derivative that retains the shape that the antibody recognizes as a PAH molecule.

When water samples with low PAH levels are added to the sensor chamber (which is already flooded with a solution of anti-PAH antibodies), the antibodies have little to bind with and are thus free to attach to the surrogate-coated beads, providing a strong fluorescent glow and electric signal. In water samples with high PAH concentrations, on the other hand, a large fraction of the antibodies bind with the environmental contaminants. That leaves fewer to attach to the surrogate-coated beads, which consequently provides a fainter glow and a weaker electric signal.

During the Elizabeth River study, the biosensor measured PAH concentrations that ranged from 0.3 to 3.2 parts per billion, with higher PAH levels closer to the dredge site. In Yorktown Creek, the biosensor showed that PAH levels in runoff peaked 1 to 2 hours after the rain started, with peak concentration of 4.4 parts per billion.

Comparison of the biosensor's field readings with later readings from a mass spectrometer at VIMS showed that the biosensor is just as accurate as the more expensive, slower, and laboratory-bound machine.

A valuable field tool

Spier says"Using the biosensor allowed us to quickly survey an area of almost 900 acres around the Elizabeth River dredge, and to provide information about the size and intensity of the contaminant plume to engineers monitoring the dredging from shore. If our results had shown elevated concentrations, they could have halted dredging and put remedial actions in place."

Unger adds"measuring data in real-time also allowed us to guide the collection of large-volume water samples right from the boat. We used these samples for later analysis of specific PAH compounds in the lab. This saved time, effort, and money by keeping us from having to analyze samples that might contain PAHs at levels below our detection limit."

"Biosensors have their constraints and optimal operating conditions," says Kaattari,"but their promise far outweighs any limitations. The primary advantages of our biosensor are its sensitivity, speed, and portability. These instruments are sure to have a myriad of uses in future environmental monitoring and management."

One promising use of the biosensor is for early detection and tracking of oil spills."If biosensors were placed near an oil facility and there was a spill, we would know immediately," says Kaattari."And because we could see concentrations increasing or decreasing in a certain pattern, we could also monitor the dispersal over real time."

Source

High Temperature Milestone Achieved in Silicon Spintronics

The electron possesses an internal angular momentum called the spin. The International Technology Roadmap for Semiconductors has identified the electron's spin as a new state variable that should be explored as an alternative to the electron's charge for use beyond Moore's Law, a projection named after Intel co-founder Gordon E. Moore. Moore predicted in 1965 that the number of transistors per unit area in an integrated circuit would double approximately every two years as advances in fabrication technology enabled the devices to be made smaller. Although this approach has been remarkably successful, critical device dimensions now approach atomic length scales, so that further size scaling becomes untenable."Researchers have been forced to look beyond the simple reduction of size to develop future generations of electronic devices," states NRL senior scientist Dr. Berry Jonker."Electrical generation, manipulation and detection of significant spin polarization in silicon at temperatures that meet commercial and military requirements are essential to validate spin as an alternative to charge for a device technology beyond Moore's Law."

Using ferromagnetic metal / silicon dioxide contacts on silicon, NRL scientists Connie Li, Olaf van 't Erve and Jonker electrically generate and detect spin accumulation and precession in the silicon transport channel at temperatures up to 225°C, and conclude that the spin information can be transported in the silicon over distances readily compatible with existing fabrication technology. They thus overcome a major obstacle in achieving control of the spin variable at temperatures required for practical applications in the most widely utilized semiconductor.

To make a semiconductor spintronic device, one needs contacts that can both generate a current of spin-polarized electrons (called a spin injector), and detect the spin polarization of the electrons (spin detector) in the semiconductor. Because the magnetic contact interface is likely to introduce additional scattering and spin relaxation mechanisms not present in the silicon bulk, the region of the semiconductor directly beneath the contact is expected to be a critical factor in the development of any future spin technology. The NRL scientists probe the spin environment directly under the magnetic metal / silicon dioxide contact using the three terminal geometry illustrated in the accompanying

figure

. Demonstration of spin precession and dephasing in a magnetic field transverse to the injected spin orientation, known as the Hanle effect, is conclusive evidence of spin accumulation, and enables a direct measure of the spin lifetime, a critical parameter for device operation. The NRL researchers observed Hanle precession of the electron spin accumulation in the silicon channel under the contact for biases corresponding to both spin injection and extraction, and determine the corresponding spin lifetimes.

Electronic states can form at the contact interface and introduce deleterious effects for both charge and spin transport. These undesirable states can serve as traps which prevent propagation of either charge or spin in the silicon channel. In bulk silicon, the spin lifetime is known to depend upon the carrier density, and generally decreases as the electron density increases.."In this study we show that the spin lifetime determined from our measurements changes systematically as one changes carrier concentration of the particular silicon sample used," adds Jonker."Our results were obtained for a number of different carrier densities and show this trend, thus making it very clear that we obtain spin injection and accumulation in the silicon itself rather than in interface defect states." The result of this research rules out spin accumulation in interface states and demonstrates spin injection, accumulation and precession in the silicon channel.

Source

Using Solar Power to Sterilize Medical Instruments

The student's used Capteur Soleil, a device created decades ago by French inventor Jean Boubour to capture the energy of the sun in places where electricity -- or fuel of any kind -- is hard to get. In attaching an insulated box containing the autoclave, the students transform the device into a potential lifesaver.

The Capteur Soleil, which sits outside Rice's Oshman Engineering Design Kitchen, looks something like an ultramodern lawn swing. Its spine is a steel A-frame, and a bed of curved mirrors beneath the frame produces steam by focusing sunlight along a steel tube at the frame's apex. Rather than pump steam directly into the autoclave, the Rice team's big idea was to use the steam to heat a custom-designed conductive hotplate.

"It basically becomes a stovetop, and you can heat anything you need to," said Sam Major, a member of the team with seniors Daniel Rist, David Luker and William Dunk, all mechanical engineering students."As long as the autoclave reaches 121 Celsius for 30 minutes (the standard set by the Centers for Disease Control and Prevention), everything should be sterile, and we've found we're able to do that pretty easily."

He said one person could easily adjust the Capteur Soleil by ratcheting up the back leg to align the mirrors with the sun. Within half an hour of receiving strong sunlight, the Capteur Soleil will begin to produce steam, which will in turn heat the patterned hotplate and then the standard-issue, FDA-approved autoclave. With good midday sun, Major said, it takes 40 minutes to an hour to begin significant heating of the autoclave.

The autoclave, which looks like a tricked-out pressure cooker, has a steamer basket inside."We put about an inch of water inside, followed by the basket with the tools and syringes," Major said."We've used some biological spores from a test kit, steamed them, and then incubated them for 24 hours and they came back negative for biological growth. That means we killed whatever was in there."

The autoclave, tucked inside a plywood frame, is wrapped in silicon-based Thermablok insulation, which has the highest R-value of any known material and is a spinoff from NASA research into thermal protection for the space shuttle."This thin layer does most of the work," Major said."We used standard pink insulation around the inside just to make the box stronger."

"This is really the latest iteration of a much larger project," said Doug Schuler, the team's faculty adviser and an associate professor of business and public policy at Rice's Jones Graduate School of Business."We already have a version of the Capteur Soleil being used in Haiti for cooking, but we felt it could do more."

Source

Portable Tech Might Provide Drinking Water, Power to Villages

Such a technology might be used to provide power and drinking water to villages and also for military operations, said Jerry Woodall, a Purdue University distinguished professor of electrical and computer engineering.

The alloy contains aluminum, gallium, indium and tin. Immersing the alloy in freshwater or saltwater causes a spontaneous reaction, splitting the water into hydrogen and oxygen molecules. The hydrogen could then be fed to a fuel cell to generate electricity, producing water in the form of steam as a byproduct, he said.

"The steam would kill any bacteria contained in the water, and then it would condense to purified water," Woodall said."So, you are converting undrinkable water to drinking water."

Because the technology works with saltwater, it might have marine applications, such as powering boats and robotic underwater vehicles. The technology also might be used to desalinate water, said Woodall, who is working with doctoral student Go Choi.

A patent on the design is pending.

Woodall envisions a new portable technology for regions that aren't connected to a power grid, such as villages in Africa and other remote areas.

"There is a big need for this sort of technology in places lacking connectivity to a power grid and where potable water is in short supply," he said."Because aluminum is a low-cost, non-hazardous metal that is the third-most abundant metal on Earth, this technology promises to enable a global-scale potable water and power technology, especially for off-grid and remote locations."

The potable water could be produced for about$1 per gallon, and electricity could be generated for about 35 cents per kilowatt hour of energy.

"There is no other technology to compare it against, economically, but it's obvious that 34 cents per kilowatt hour is cheap compared to building a power plant and installing power lines, especially in remote areas," Woodall said.

The unit, including the alloy, the reactor and fuel cell might weigh less than 100 pounds.

"You could drop the alloy, a small reaction vessel and a fuel cell into a remote area via parachute," Woodall said."Then the reactor could be assembled along with the fuel cell. The polluted water or the seawater would be added to the reactor and the reaction converts the aluminum and water into aluminum hydroxide, heat and hydrogen gas on demand."

The aluminum hydroxide waste is non-toxic and could be disposed of in a landfill.

The researchers have a design but haven't built a prototype.

Source

Chemist Designs New Polymer Structures for Use as 'Plastic Electronics'

Those tricks improve the properties of certain organic polymers that mimic the properties of traditional inorganic semiconductors and could make the polymers very useful in organic solar cells, light-emitting diodes and thin-film transistors.

Conductive polymers date back to the late 1970s when researchers Alan Heeger, Alan MacDiarmid and Hideki Shirakawa discovered that plastics, with certain arrangements of atoms, could conduct electricity. The three were awarded the 2000 Nobel Prize in Chemistry for the discovery.

Jeffries-EL, an Iowa State assistant professor of chemistry, is working with a post-doctoral researcher and nine doctoral students to move the field forward by studying the relationship between polymer structures and the electronic, physical and optical properties of the materials. They're also looking for ways to synthesize the polymers without the use of harsh acids and temperatures by making them soluble in organic solvents.

The building blocks of their work are a variety of benzobisazoles, molecules well suited for electrical applications because they efficiently transport electrons, are stable at high temperatures and can absorb photons.

And if the polymers are lacking in any of those properties, Jeffries-EL and her research group can do some chemical restructuring.

"With these polymers, if you don't have the properties you need, you can go back and change the wheel," Jeffries-EL said."You can change the chemical synthesis and produce what's missing."

That, she said, doesn't work with silicon and other inorganic materials for semiconductors:"Silicon is silicon. Elements are constant."

The National Science Foundation is supporting Jeffries-EL's polymer research with a five-year,$486,250 Faculty Early Career Development grant. She also has support from the Iowa Power Fund (a state program that supports energy innovation and independence) to apply organic semiconductor technology to solar cells.

The research group is seeing some results, including peer-reviewed papers over the past two years inPhysical Chemistry Chemical Physics, Macromolecules, the Journal of Polymer Science Part A: Polymer Chemistry,and theJournal of Organic Chemistry.

"This research is really about fundamental science," Jeffries-EL said."We're studying the relationships between structure and material properties. Once we have a polymer with a certain set of properties, what can we do?"

She and her research group are turning to the molecules for answers.

"In order to realize the full potential of these materials, they must be engineered at the molecular level, allowing for optimization of materials properties, leading to enhanced performance in a variety of applications," Jeffries-EL wrote in a research summary."As an organic chemist, my approach to materials begins with small molecules."

Source

Cells Send Signals Via Membrane Nanotubes

For nearly ten years, researchers have known that cells can"grow" ultra-thin tubes named tunnelling nanotubes (TNTs) between one another. These nanotubes -- the length of two to three cells and just 1/500th the thickness of a human hair -- are connections that develop between nearly all cell types to form a communication channel different from any previously known mechanisms.

In 2010, Dr. Xiang Wang and Professor Hans-Hermann Gerdes -- colleagues at the University of Bergen's Department of Biomedicine -- discovered that electrical signals were being passed through nanotubes from one cell to another at high speed (roughly 1-2 m/sec). Their research receives funding under the Research Council's large-scale research programme Nanotechnology and New Materials (NANOMAT).

The breakthrough

In their key experiment, Dr Wang used fluorescent dye that changes in intensity as the electric potential of the cell membrane changes. When two cells connected by forming a nanotube, he poked into one of them with a microinjection needle to depolarise that cell's membrane potential. This caused the fluorescent indicator on the cell membrane to light up like a firework, and it was soon followed by a similar light display in the cell on the other end of the nanotube.

The breakthrough discovery began with an experiment demonstrating intercellular transmission of electrical signals via nanotubes in 2007. The researchers then carried out similar trials with a number of other cell types, observing similar occurrences.

"We confirmed that this is a common phenomenon between cells," explains Professor Gerdes."Still, this characteristic is not in every cell type."

The experiment was replicated a number of times to obtain statistically reliable data. The electrophysiology group at the University of Bergen took precise conductivity measurements of the cell systems to determine the strength of the electrical coupling. In autumn 2010 the results were published inProceedings of the National Academy of Sciences (PNAS).

Short lifespan

Intercellular nanotubes are far from permanent. Most of them last only a few minutes. This means the researchers cannot predict where and when the cells will form nanotube connections.

"It is truly painstaking work," says Professor Gerdes."You may sit there examining cells for hours through a microscope without seeing a single tube. If you are lucky, however, you catch sight of a nanotube being created and can film the event."

To raise the likelihood of finding nanotubes, the researchers developed a micro-matrix consisting of thousands of points and bridges on a plate surface. Smaller than a postage stamp, the plate is covered by a nano-structured material to which the cells adhere. The researchers place one cell onto each point and hope that nanotubes will form along the bridges between the points. The camera is focused on these bridges.

Once the nanotubes have been established, the researchers manipulate the cells at specified times; meanwhile the microscope is programmed to photograph, say, 50 preselected points every five minutes. The team can thus obtain data about many nanotube connections in a short time.

How do cells do this?

Dr. Wang quickly discovered that the mere presence of a nanotube was not sufficient to transmit an electrical signal. There had to be another mechanism involved as well.

Many cells form tiny membrane pores with each other called gap junctions, which are made up of ring-shaped proteins. Back in the 1960s it was discovered that directly adjacent cells could exchange electrical impulses through these gap junctions. What Dr Wang found was that one end of the nanotube was always connected to cells by a gap junctions before it transmitted its electrical impulses.

He also found that in some coupled cells voltage-gated calcium channels were involved in the forwarding of the incoming signals. When the electrical signal being sent through the nanotube reaches the membrane of the receiving cell, the membrane surface is depolarised, opening the calcium channel and allowing calcium -- a vital ion in cell signalling -- to enter.

"In other words," explains Professor Gerdes,"there are two components: a nanotube and a gap junction. The nanotube grows out from one cell and connects to the other cell through a gap junction. Only then can the two cells be coupled electrically."

Controls embryonic cells?

Now the scientists are seeking answers as to why the cells send signals to each other in this way.

"It's quite possible that the discovery of nanotubes will give us new insight into intercellular communication," asserts Professor Gerdes."The process could explain how cells are coordinated during embryo growth. In that phase cells travel long distances -- yet they demonstrate a kind of collective behaviour, and move together like a flock of birds can."

Nanotubes may also be a factor in explaining cell movement associated with wound healing, since cells move toward a wound in order to close it. We already know that electrical signals are somehow involved in this process; scientists can only speculate as to whether nanotubes are involved here as well, stresses Professor Gerdes.

Perhaps brain cells, too?

In terms of electronic signal processing, the human brain surpasses all other organs. If this same signalling mechanism proves to be present in human brain cells, it could add a new dimension to understanding how the brain functions. Communication channels involving synapses and dendrites that are already identified differ widely from nanotubes.

The Bergen-based neuroscientists see this research as an opportunity to formulate better explanations for phenomena related to consciousness and electrical connections in the brain. In the project"Cell-to-cell communication: Mechanism of tunnelling nanotube formation and function," they are now studying precisely how nanotube mechanisms function in brain cells.

Professor Gerdes is currently conducting research at the European Molecular Biology Laboratory in Heidelberg. By studying the electrical connections in vivo he hopes to figure out how the mechanisms work in live subjects. The results could enhance understanding of diseases that occur when cell mechanisms fail to function properly.

Source